: Indicates it is a tarball archive containing all necessary system files, including HTML GUI files, for the access point to operate standalone. Key Differences: k9w7 vs. k9w8
After booting with K9W7 firmware:
AP803 Access Point Module * Autonomous AP IOS Software. WIRELESS LAN (ap1g3-k9w7-tar.153-3.JH1.tar) * Lightweight AP IOS Software. Cisco IOS Release 15.9(3)M2a - Cisco ap1g3-k9w7-tar
| Symptom | Likely Cause | Solution | |---------------------------------|----------------------------------------------|--------------------------------------------------------------------------| | Module not detected on PCIe | Insufficient power during boot sequence | Check 3.3 V rail for droop < 5%; add 470 µF capacitor near connector | | Throughput drops to < 100 Mbps | DFS event on 5 GHz band | Manually select non‑DFS channel or enable “channel reuse” mode | | Intermittent disconnections | Overheating (> 105°C die temp) | Improve airflow or install HS‑TAR‑01 heatsink | | High latency ( > 20 ms ) | Background scan from roaming daemon | Set scan_interval=0 to disable autonomous scanning | | WPA3 authentication fails | Incorrect certificate chain | Verify intermediate CA is loaded; use ap1g3_cert_mgr verify |
: Denotes the generation and architectural group of the hardware. The "g3" identifier maps to the third-generation low-end enterprise/outdoor radio chipsets, specifically powering hardware such as the Cisco Aironet 1532i and 1532e outdoor access points. : Indicates it is a tarball archive containing
If you need help finding specific or troubleshooting commands for this firmware, please let me know! _verified_: Ap1g3-k9w7-tar
ap: set IP_ADDR 192.168.1.50 ap: set NETMASK 255.255.255.0 ap: set DEFAULT_ROUTER 192.168.1.1 ap: set SERVER_IP 192.168.1.100 WIRELESS LAN (ap1g3-k9w7-tar
"archive_id": "ap1g3-k9w7-tar-0001", "created_at": "2026-03-23T12:00:00Z", "archive_sha256": "SHA256(...)", "files": [ "path":"bin/app","size":823456,"sha256":"...", "path":"conf/config.yml","size":234,"sha256":"..." ], "metadata":"env":"prod","origin":"ci-42"
: Indicates it is a tarball archive containing all necessary system files, including HTML GUI files, for the access point to operate standalone. Key Differences: k9w7 vs. k9w8
After booting with K9W7 firmware:
AP803 Access Point Module * Autonomous AP IOS Software. WIRELESS LAN (ap1g3-k9w7-tar.153-3.JH1.tar) * Lightweight AP IOS Software. Cisco IOS Release 15.9(3)M2a - Cisco
| Symptom | Likely Cause | Solution | |---------------------------------|----------------------------------------------|--------------------------------------------------------------------------| | Module not detected on PCIe | Insufficient power during boot sequence | Check 3.3 V rail for droop < 5%; add 470 µF capacitor near connector | | Throughput drops to < 100 Mbps | DFS event on 5 GHz band | Manually select non‑DFS channel or enable “channel reuse” mode | | Intermittent disconnections | Overheating (> 105°C die temp) | Improve airflow or install HS‑TAR‑01 heatsink | | High latency ( > 20 ms ) | Background scan from roaming daemon | Set scan_interval=0 to disable autonomous scanning | | WPA3 authentication fails | Incorrect certificate chain | Verify intermediate CA is loaded; use ap1g3_cert_mgr verify |
: Denotes the generation and architectural group of the hardware. The "g3" identifier maps to the third-generation low-end enterprise/outdoor radio chipsets, specifically powering hardware such as the Cisco Aironet 1532i and 1532e outdoor access points.
If you need help finding specific or troubleshooting commands for this firmware, please let me know! _verified_: Ap1g3-k9w7-tar
ap: set IP_ADDR 192.168.1.50 ap: set NETMASK 255.255.255.0 ap: set DEFAULT_ROUTER 192.168.1.1 ap: set SERVER_IP 192.168.1.100
"archive_id": "ap1g3-k9w7-tar-0001", "created_at": "2026-03-23T12:00:00Z", "archive_sha256": "SHA256(...)", "files": [ "path":"bin/app","size":823456,"sha256":"...", "path":"conf/config.yml","size":234,"sha256":"..." ], "metadata":"env":"prod","origin":"ci-42"